 | ||||
Looking for a job in the construction industry? Visit our sponsor at DryWallFlorida.com
| ||||
Patent Pending: 61-281643
DryWallCarolina is sponsored by DryWallFlorida.com
PO Box 26492 Greenville SC 29616
Phone: 864-505-2641 - Fax: 864-676-2882 - Email
DWC Drywall Repair Plug: 1756270898
Choosing The Best Drywall Fastener
Nails are common fasteners, but also pose a potential problem. They may pop out when the wood to which they are attached loses moisture and shrinks. The moisture content of most framing lumber is 15 to 19 percent.
After installation, the moisture content will drop about 10 percent. This may not happen until the first heating season. One of the signs of the shrinking lumber could appear as nails popping out of the drywall.
Special drywall nails such as annular-ringed and cement-coated nails, help ensure good anchoring and minimize popping. When choosing nails select the shortest nail that will do the job. In experiments conducted by the Forest Products Laboratory and Perdue University, shorter nails usually resulted in less space between the stud and the nailing surface after the wood shrinks. Quite simply this means fewer nails will pop out.
Most professional drywall contractors choose to use Phillips-head drywall screws. They cut into the wood, hold tighter, and are much less likely to work loose than nails. These screws are designed to depress the face paper without tearing it. You can set the screw guns so that they automatically insert the screws slightly below the surface of the wallboard.
This process gives you more uniformity and helps make the finishing job easier when you apply joint compounds and tape. Screws are best if you want to fix a hole in the wall using old fashioned methods. Some of todays drywall repair products require a quick frame process or some kind of backing. Backing adds strength to many repairs when fixing a hole in the wall.
Some pros like using a glue with nails or screws.Using an adhesive means you use fewer nails or screws, and still provides strength equal to or greater than nails or screws alone. The pattern of the adhesive is important for structural strength. Use a single bead on studs and joists that fall in the center of wallboards. Apply adhesive in an S pattern on studs and joists where wallboard edges meet. Work in small areas when using adhesive, and don't apply more than can be covered in 15 minutes. If it's exposed too long, it'll begin hardening and skimming, which will prevent a good bond between the panels and studs.
DWC Drywall Repair Plugs don't require any drywall skills.
| ||||
| ||||
5 Painting Mistakes:
Not Covering Furniture - Buying Bargain Paint - Latex Over an Oil Based - Masking & Taping - Buying More Paint
Helpful Things To Know:
| ||||
DWC Resizable Drywall Repair Plugs
Return the structural integrity to damaged walls & ceilings
DWC Fire Plugs meet ASTM Standards and all US Building Codes for repairing Commercial Fire Rated Walls.
| ||||
| ||||
| ||||
When setting the patch make sure that joint compound is coming out of all the face material holes. Stick pins can help to hold the patch in place while your wiping it down
Don't be afraid of wiping too hard. Our face material is made from a tough composite and is strong enough not to be bothered by any amount of over wiping or sanding.
Because our face material is less than 1/16 inch thick, you'll only need to apply very thin coats of joint compound to achieve good results for your drywall repair.
When throughly dry, sand and recoat with joint compound. When dry, run your hand across the entire repair. Recoat and sand only if you feel it's necessary.
Once marked, use a drywall saw or utility knife to cut the circle out. Cut the circle out of the wall. Be sure to stay on the outside of the line
Double check your fit by placing the plug into the hole before you apply joint compound. One inch of movement between the drywall repair plug and hole is acceptable using DWC Drywall Repair Plugs..
Step 3: When patch is set apply a thin coat of joint compound. Try to keep your work as smooth as possible to cut down on sanding.
Step 2: Load the plug with joint compound as shown and place in hole. Wipe patch down until it's flush and tight with the wall.
Step 1: Resize the plug or use the package holder template to mark the damaged area of the drywall you need removed for repair.
Choosing The Best Drywall Fastener is Easier Than You Think!
| ||||
Drywall repair patch for holes up to 4 inches in diameter in 1/2 Inch standard or 5/8 inch thick fire rated drywall. Perfect for doorknob damage, insulation holes and many other small holes on most residential remodel projects. Commercial uses include outdated pipe and/or sprinkler supply line holes, empty can lights, empty electrical boxes and pass through holes.
Drywall repair patch for holes up to 8 inches in diameter in 1/2 Inch standard or 5/8 inch fire rated drywall. Perfect drywall repair for fist sized holes and many other holes on residential projects. Commercial uses include wire pulling holes,outdated HVAC duct holes and just about any sized empty electrical box or can light.
Proper installation requires "Backing".
Drywall repair patch for holes up to 12 inches in diameter in 1/2 Inch standard or 5/8 inch thick fire rated drywall. Great for larger areas and empty chimney/ventilation holes in older commercial and residential buildings.
Proper installation requires "Backing".
